Dake Model 150H - 907004 User Manual download pdf

125H Press & 150H Press 10/02

INSTRUCTIONS AND PARTS

LIST FOR MODEL 125H & 150H

HAND-OPERATED HYDRAULIC

PRESS

SETTING UP THE PRESS FOR OPERATION

For shipping convenience, the gauge, pump handle, hoist crank, screw nose and base angles

were removed from the press. Assemble these parts to the press in the following order:

1. Bolt the base angles to the uprights using the four bolts and nuts furnished. Shoulder the

base angles against the stops on the uprights.

2. Install the pressure gauge using a hydraulic sealant to ensure a sealed fit.

3. Insert pump handle into handle socket and fasten in place by means of the setscrew on

top of the handle socket.

4. CAUTION! Place the hoist crank on the lift drum shaft. The table is raised to the

desired height by turning the crank after removing the table pins. Check to make

sure the hoist cable is tracking correctly. Run the table channels from top to

bottom. The cable should be on each of the two upper pulleys and should track

back and forth on the cable drum. Always place table pins under the table

channels before releasing the hoist crank when positioning the table channels for

cable tracking, servicing, or set-up for desired work opening. If a tracking problem

exists, contact the Dake factory for instructions. Be sure all table pins are fully

inserted in place before applying pressure. Always remove or release pressure on

the cable before pressure is applied.

5. Fasten nosepiece to the end of the screw using the thumbscrew included.

OPERATIONS AND CONTROLS

The operator should acquaint himself with the use of the following controls:

1. The pump handle is the pressure supply source and is manually operated with an up and

down motion.

2. Item number 45 (Part no. 10631) is the release valve handwheel. Always keep it firmly

closed when operating the press and it should only be opened when releasing the

pressure to allow the ram to return.

3. By turning Item 25 (Part No. 701760), the ram screw can be adjusted into or out of the

piston assembly. Always keep the portion of the screw extending out of the piston as

short as possible. It is advisable to raise the table one or two sets of holes rather than

running the screw out to its limit of travel. NEVER EXCEED THE RECOMMENDED

STROKE OF 8 INCHES FOR THIS PRESS. EXCEEDING THE STROKE WILL CAUSE

DAMAGE TO THE INNER PACKINGS.

4. The two combination table plates-v blocks provided are used for supporting the work

while it is being straightened.

FILLING THE PRESS WITH OIL

It is extremely important that new, clean, light hydraulic oil be used in this press, Mobil DTE 24

or an equivalent. It is strongly recommended that the oil be filtered to remove any possible

dirt. The piston should be in its maximum upper position when filling the reservoir. Fill the

reservoir with 14 quarts of oil. UNDER NO CIRCUMSTANCES USE OLD DIRTY OIL. Next

remove the screw plug from the gauge extension on top of the workhead, close the release

valve handwheel and pump oil into the workhead until oil is visible in the stand pipe. This will

remove all air from the chamber above the piston. If oil leaks by the piston, the reservoir

should be drained and refilled (14 quarts of oil) with the piston in the top position.

1 2 3 4 5 6

Summary of Contents

Page 1 - HAND-OPERATED HYDRAULIC

125H Press & 150H Press 10/02 1 INSTRUCTIONS AND PARTS LIST FOR MODEL 125H & 150H HAND-OPERATED HYDRAULIC PRESS SETTING UP THE

Page 2

125H Press & 150H Press 10/02 2 ORDERING INFORMATION Please order all parts by number and name. Also mention model number and serial number as

Page 3 - SYMPTOM CAUSE SOLUTION

125H Press & 150H Press 10/02 3 TROUBLE SHOOTING – DAKE HAND HYDRAULIC PRESSES PUMP PACKING LEAKAGE If oil leaks past the pump packing, tight

Page 4 - HANDPUMP ASSEMBLY

125H Press & 150H Press 10/02 4 HANDPUMP ASSEMBLY Item Qty Description Part No. 1 1 Pump Body 546 2 3 Ball va

Page 5 - WORKHEAD ASSEMBLY

125H Press & 150H Press 10/02 5 WORKHEAD ASSEMBLY Item Qty Description Part No. 21 1 Pump Gasket 591 22 1

Page 6 - FRAME ASSEMBLY

125H Press & 150H Press 10/02 6 Item Qty Description Part No. 39 1 1 Gauge Bushing 71268 81384 40 1 Gauge Extension 628 41 4 Roller

Related models: Model 125H - 907004

Comments to this Manuals

No comments

Dake Model 150H - 907004 User Manual

Browse online or download User Manual for Equipment Dake Model 150H - 907004. Dake Model 150H - 907004 User Manual [de]

Summary of Contents

Related models: Model 125H - 907004

Comments to this Manuals

Related products and manuals for Equipment Dake Model 150H - 907004